Page 3 of 4
Re: Large Rifle Primers
Posted: Thu Jan 18, 2024 5:50 am
by bpcrshooter62
Re: Large Rifle Primers
Posted: Thu Jan 18, 2024 8:53 am
by desert deuce
UP Here?
Where is UP HERE? Buffalo, NY, Alberta, Canada, Plentywood, Montana ?
Re: Large Rifle Primers
Posted: Thu Jan 18, 2024 8:55 am
by bpcrshooter62
DD Saskatchewan Canada lol
Re: Large Rifle Primers
Posted: Fri Jan 19, 2024 3:22 pm
by RB1Shooter
BPCR - you might check-out "Everything Black Powder" on YouTube. I would suggest the toilet paper recipe.
Re: Large Rifle Primers
Posted: Fri Jan 19, 2024 3:34 pm
by bpcrshooter62
RB1Shooter what the H is that ? lol
Re: Large Rifle Primers
Posted: Fri Jan 19, 2024 7:26 pm
by VenisonRX
bpcrshooter62 wrote: ↑Fri Jan 19, 2024 3:34 pm
RB1Shooter what the H is that ? lol
I’ve seen what he’s talking about. Actually it’s pretty interesting. A guy makes black powder using a roll of toilet paper as the carbon source and the powder ends up faster and cleaner than Swiss with his batches. I felt the claim was a bit out there until actually watching it and looking into his methods. Not bad really. He does a lot more than most home powder makers do to ensure consistency and faster better burning products. Most of his result is in the process but he does try other carbon sources as a comparison and most of them weren’t as good as Swiss except the toilet paper (brand made a difference) and I think balsa wood but don’t quote me on the last one.
Re: Large Rifle Primers
Posted: Fri Jan 19, 2024 8:39 pm
by RB1Shooter
The balsa wood was good but, if I remember correctly, it was dirtier than Swiss. The TP carbon source, you need to use is Cottonel. He tried another brand and it wasn't near as good. He also has a 2 part program where he goes through and shows you how to make the powder. He does a good job and fun to watch.
Just google search "youtube everything black powder" and you'll find him.
Re: Large Rifle Primers
Posted: Fri Jan 26, 2024 8:38 am
by jackrabbit
No, it was superior to Swiss in that it was more powerful and cleaner. I just watched it. The cottonelle toilet paper one was pretty equal to Swiss
Re: Large Rifle Primers
Posted: Fri Jan 26, 2024 6:58 pm
by patchbox
That’s a very interesting series of videos. I wonder if the ingredients could be ball milled slightly damp? I’d be concerned if that whole mess blew - lead balls flying everywhere. Other thing is if something goes off during the corning process. Those pucks are so dense that they would go off extremely fast if they had a low enough moisture content and they ignited. It’s not if something happens, it’s when. Only way I’d attempt that is if I had a big spread of land where no one else was around. Run a 100 yards of extension cord out to that ball mill.
Re: Large Rifle Primers
Posted: Sat Jan 27, 2024 10:24 pm
by RB1Shooter
I believe he has a video showing how he ball mills. I may be thinking of another but I'm pretty sure he does.
Re: Large Rifle Primers
Posted: Sun Jan 28, 2024 12:16 pm
by patchbox
Ok, yeah, I took a look at the entire process he lays out. It’s actually not that bad from a safety standpoint. He keeps everything in small batches. When ball milling the powder is not compressed so even if it did ignite the burning speed is going to be slow. I saw his video on how he corns the pucks through one of those hand grinding machines - again, very small batches. Looks like something I’d like to try but not where I currently live - 2 bedroom condo in California. Haha! I’ll wait till I retire and move to another state.
Re: Large Rifle Primers
Posted: Mon Jan 29, 2024 8:55 am
by Luke
He has changed a few things, and has promised a new set of videos on his current process. He's currently milling with brass spheres.
Re: Large Rifle Primers
Posted: Mon Jan 29, 2024 10:08 am
by patchbox
Yeah, I was thinking the same thing - brass or bronze spheres.
Re: Large Rifle Primers
Posted: Mon Jan 29, 2024 10:42 am
by patchbox
McMaster-Carr has 260 Brass balls
from 1/16” all the way up to 3/4”
Re: Large Rifle Primers
Posted: Mon Jan 29, 2024 10:44 am
by patchbox
I’m thinking a mix of 1/4” diameter, 1/2” diameter & 3/4” diameter would be a good start.