Page 1 of 1
Who made this tang sight?
Posted: Fri Mar 01, 2024 7:41 pm
by TexasMac
A shooting buddy of mine has the rear tang sight in the photos. Neither he nor I have any idea who made it. Iโm guessing itโs a โone offโ made by a good machinist. Can anyone identify the maker?
BTW, the eyecup locks the windage only. The small nut on the elevator screw locks vertical movement.
Wayne
Re: Who made this tang sight?
Posted: Sat Mar 02, 2024 10:43 am
by Tomklinger
JAK!
Was this a test?
Tom Klinger
Re: Who made this tang sight?
Posted: Sat Mar 02, 2024 12:31 pm
by TexasMac
Tomklinger wrote: โSat Mar 02, 2024 10:43 am
JAK!
Was this a test?
Tom Klinger
Tom,
Thanks for that insightful comment. There's always a comedian in the crowd.
See you next month.
Wayne
Re: Who made this tang sight?
Posted: Sat Mar 02, 2024 2:13 pm
by John Bly
John King? Don't know if he ever took the time to make a sight. He was a good machinist.
Re: Who made this tang sight?
Posted: Sat Mar 02, 2024 2:20 pm
by Tomklinger
Desert Deuce,
See!! Some people think I have a sense of humor!
Tom Klinger
Re: Who made this tang sight?
Posted: Sat Mar 02, 2024 6:37 pm
by TexasMac
John Bly wrote: โSat Mar 02, 2024 2:13 pm
John King? Don't know if he ever took the time to make a sight. He was a good machinist.
Thanks John,
John King is a good guess but it's not him. His middle initial is "P". I've had a phone conversation with him recently. At 74 he's pretty much retired but does continue to accept some limited gunsmithing work.
Wayne
Re: Who made this tang sight?
Posted: Sat Mar 02, 2024 7:48 pm
by TexasMac
I also posted the photos on the ASSRA forum. A guy with the handle of โnineteen76โ provided the following. The machinist that made the sight is:
Jim Keller
Ashton, SD
(605) 472-1109
He sets up at most Gun Shows here in South Dakota selling various gunsights.
There was one listed on Gunbroker not too long ago but I cannot find the ad.
Here is one of his sights on a Wind River Hepburn that I sold a while back (Rifle and Tang Sight made in SD)
https://www.gunsinternational.com/guns- ... =101832879
======================================
I ran a search on him & found he now lives at the following address with the same phone number. Other than it being shorter and with a slightly different style staff base the sight construction in the link above looks identical.
Jim A Keller,
Age 71
823 S. Spring Ave
Sioux Fall, SD 57104
605-472-1109
Wayne
Re: Who made this tang sight?
Posted: Sat Mar 02, 2024 8:03 pm
by bobw
Jim is a good guy and very knowledgeable about original sights. He carries an amazing collection for sale when he sets up at a show..bobw
Re: Who made this tang sight?
Posted: Sat Mar 02, 2024 9:12 pm
by marlinman93
John King was actually a bad guess in my opinion. John King does wonderful work, and would never have built a sight that crude.
Re: Who made this tang sight?
Posted: Sun Mar 03, 2024 8:04 am
by bobw
Marlinman no need to.be so critical. That sight was made long before cnc equipment while it lacks the polished refined look of any MVA sight it is far better than any Pedersoli you can find. Bobw
Re: Who made this tang sight?
Posted: Tue Mar 05, 2024 12:15 pm
by Raymond Hanson
I see you figured out it was J Keller. I have two of his sights from back in the old days. I did have them converted to Soule sights but I still use the one on my .22 Sharps all the time. They have been very good sights. Raymond Hanson